Tools

This simple tool is designed to remove and install the static bearing in the shock ends of many modern rear shocks. Machined from durable stainless steel this compact tool allows the user to remove and install the DU bushings without resorting to hammers and punches. The coarse acme thread keeps the constant turning to a minimum.

1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.

For use with the Decade Chain Tool this AXS Mid Plate is required for the SRAM AXS Road and the new MTB Transmission Flat Top chains. This part is not needed for other 12spd chains from various manufacturers. The mid plate is visually differentiated from the other Decade mid plates by three dots on the face of the plate.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.

The lever setter is a unique tool that works in conjunction with our HAG (or other hanger allignment tool) to set brake and shifter levers at the same height from side to side. The tool temporarily replaces the headset top cap and allows you to thread a hanger alignment tool into the lever setter. Use the HAG indicator to set levers the same from one side of the bar to the other. Once you're satisfied with your lever placement simply remove the tool and replace your headset top cap and go ride. Compatibility: Requires a star nut or compression plug with a M6x1 thread. Works with road and mountain shifters and brake levers. Compatible with most hanger alignment tools on the market. Recommendations: It's advised to use a spacer on top of the stem to help align the lever setter with the steer tube. This will reduce the impact the quality of the cut on the steer tube has on the function of the tool. The supplied threaded stud can be replaced with a longer one if needed.

This dedicated socket is built to engage all 4 of the holes on a SRAM dub crank arm dust cap. These caps don't normally need to be removed but when you do need to work with them, few things work well. These tools feature a common 3/8" square drive like the rest of our socket range and also have a hexagonal exterior so you can mount them in a vise and use the crank arm as the lever if so desired. The sockets are also marked for the left hand thread (clockwise to loosen) this part uses. Compatible with all SRAM dub cranks, road/mountain/gravel.

The unique thing about our Saw Guide is that the clamp is open, so you can slide it around the steer tube instead of having to slide it over the end. It doesn't sound like that big of a deal but it means you can get an accurate and square cut without taking the fork off the bike and more importantly without taking all the cables out of the bike. Use this tool once for that application and it's paid for itself. Of course it will work on normal steer tubes as well and give you a nice square cut every time. The guide is two sided, one side for standard toothed metal cutting blades and the opposite side is wider for abrasive blades used to cut composites. You can also use the guide in a vise like you're probably use to and it's pretty compact if you want to travel with it. Compatible with 1" and 1.125" steer tubes Currently not compatible with cutting handlebars!

The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts. Compatibility: - Chain ring lockrings on Shimano 12spd mountain crank sets. - XT and Ultegra bottom brackets

The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. The S Group Socket Crombie is ideal for some of the newer RockShox suspension forks that are using the S group lockring spline for suspension top caps. It is also compatible with all modern Shimano and Sram cassettes.

The Stu Stick is a 44-gram rotor truing tool. Whether you want to slip it into your hydration pack for that enduro mountain bike ride or travel the world working with one of the staples of cross racing, it's up to the task. You can even use it to crack open a beer after you're done with the day's fun. - Weight: 44g - Made of aluminum

These gems are machined to precisely fit the preload adjuster cap on all modern 24mm spindle Shimano cranks. The finger spline offers good leverage to install, remove, or adjust the preload cap. We also added a 5mm hex in the center should you need a little extra leverage that a hex key provides. These are also compatible with our fit kits and with the addition of a saddle height bullet can be used to more accurately measure saddle height.

Bearing drift designed for the SRAM DUB crank platform and use with the Abbey Bike Tools Modular bearing press. SRAM recently launched a new crank platform called DUB to improve bearing durability and compatibility that modern frames have dictated. This 28.99mm spindle and its press fit bottom bracket requires some special drifts to install correctly. We worked with the crew at SRAM to develop tools for this and came up with some simple and important tweaks from a standard bearing drift. These drifts have a tapered boss that forces the small O ring into its gland. A normal drift with a square boss can easily tear the fragile O ring that helps with bearing durability. So this basic modification makes sure your bottom bracket retains the durability it was designed to have. - Comes as a set of two drifts

Suspension service is a specialty within bicycle repair, and it takes specialized tools to perform this work. One of the things that any factory tech will tell you is nice to have are sockets specifically made or altered for the low profile hex on the top of each fork leg. The lead-in or chamfer on a standard socket will greatly decrease the contact between tool and part and can easily scratch or deform those nuts. For years shops have been grinding down their sockets to remove the chamfer. The problem is that you're still often left with a loose-fitting socket that is still prone to chewing up those delicate parts. That's why we started from scratch. We made our sockets from billet aluminum to exacting tolerances to keep these parts in good shape. Fully CNC-machined with zero lead-in, they make the specialty that is suspension service a little bit easier. They feature a 3/8" square drive for use with your favorite torque wrench as well as finger splines to help run the top caps into the fork legs with those oil soaked hands. We also kept them short (1" or 25mm for all sizes) to reduce the chance of them slipping off of the top cap under torque. - Made from billet aluminum to exacting tolerances to keep form damaging the suspension - Finger splines so you can thread it easily by hand - 3/8" square drive - Short (1"/25mm for all sizes) to reduce the chance of them coming off of the top cap under torque - Made in Bend, Oregon Applications - 24mm socket - used on SRAM top caps - 26mm socket - used on Marzocchi and Reverb sealheads - 27mm socket - used on Fox and X-Fusion top caps - 30mm socket - used on the RS-1 SRAM sealhead removal tool as well as a handful of other forks. - 6-size set covers most modern suspension forks on the market: 24, 26, 27, 28, 30 and 32mm

This bottom bracket socket is for use on BSA30 12-notch bottom brackets, such as SRAM DUB, Rotor, Race Face Cinch, and many others that use this common tool interface. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use on BSA30 16-notch bottom brackets. Made with the same top shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with Chris King's T47 Bottom Bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

This bottom bracket socket is for use with Colnago's 30mm Bottom Bracket Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

This bottom bracket socket is for use with E Thirteen's BB30 bottom brackets. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with Hope's BSA30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with the Praxis M30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with the TorqTite BSA30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

This tool is compatible with all outboard bearing cups that our dual-sided Shimano socket doesn't fit, including Campagnolo, SRAM, FSA, and older Shimano. These gems start as a 7075 aluminum billet and get precisely machined. We take the time to put some nice deep finger splines in this tool so you can thread the cup into the frame by hand with those greasy fingers you haven't washed in a while. - Hard anodized and laser-engraved with torque specs. - Use your favorite 3/8" square drive ratchet or torque wrench to tighten it down.

All the awesomeness of the dual-sided tool but in a single Shimano or Campagnolo version. Updated in 2020, the single-sided tool now has the same size handle (1/2 inch) as the dual-sided tool. - When purchasing the chain whip, buy the 1/2-inch handle chain whip.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.

While most other manufacturers cast or forge their bottom bracket tools, we machine ours for greater precision. Whenever you're dealing with anodized surfaces, great care needs to be taken to keep those surfaces from getting marred, gouged, and stripped out. That can be nearly impossible with some spanner style tools, and difficult with other loose-fitting sockets. The most unique feature about this tool is the inner nub; that nub in the center of the tool is the same size as the crank spindle. What this does is give you a second point of contact that keeps the tool from coming off of the part when trying to remove stubborn cups. This dual sided socket is designed to work with the new Shimano DA-9000/XTR-BB93 bottom bracket as well 6800 Ultegra and 5800 105 11spd groups (BBR-60).

The Whip-It maximizes function and simplicity. Made from a 12-inch length of stainless steel, it gives you enough leverage to loosen even the most stubborn cassettes. The Whip-It's round handle provides comfort surpassing other flatbar-style chain whips on the market. The icing on the cake is that Abbey's signature tool, the Crombie, stores inside the handle of the Whip-It; this means the two tools you use together get stored together and travel together, creating less clutter in your tool box.

The Whip-It maximizes function and simplicity. Made from a 12-inch length of stainless steel, it gives you enough leverage to loosen even the most stubborn cassettes. The Whip-It's round handle provides comfort surpassing other flatbar-style chain whips on the market. The icing on the cake is that Abbey's signature tool, the Crombie, stores inside the handle of the Whip-It; this means the two tools you use together get stored together and travel together, creating less clutter in your tool box.