Tools

We went through extra steps to make this tool half precision measuring instrument and half pry bar. - Tolerances as tight as a quarter of a thousandth of an inch (.0063mm) in some critical dimensions of this tool. - Ability to lock in the feeler so you don't have to second-guess your measurement after bumping it on the tire. - Top half of tool will rotate out of the way of fender stays and frame tubes. - Feeler gauge stick stores inside the top half of the tool, very handy for the traveling mechanic. - T-bolt extends past the tool for access to those problematic hangers found on some modern full suspension bikes. - Compact at just under 11" ( 28cm) - Re-buildable - While ideally your HAG should be sent back for a rebuild, it is possible to do them in the field by replacing the brass bushing in the T-Bolt. - Compatible with the three most common wheel sizes (26, 27.5/650B, and 700/29)

This is an add-on kit for the popular Abbey Bike Tools Modular bearing press, adding even more versatility for the modern mechanic to deal with all the different shapes, sizes, and styles. The kit includes drifts for all common bearing sizes with a bearing inner diameter (ID) of 15mm or larger. Includes the over-axle drifts required to install bearings in DT, Zipp, and other modern captured bearing hubs. These drifts feature a 1/2" (12.7mm) ID and can be used with other presses if need be. Drifts included with this set precisely fit the following bearing sizes: - 6702 - 6703 - 6704 - 6803 - 6804 - 6902 - 6903 - 6904 - 17287 - 15267/15268

This dishing gauge is fully machined from big billets of aluminum to a final shape and accuracy that's as nice to use as it is to look at. Compatible with wheels from 20-29 inches and all hub combinations. Standoff feet are included for checking dish with the tire in place, even the big fat ones. The gauge uses a unique spring-loaded mechanism to drop the plunger. Press that little brass button on the front and the plunger will drop to the face of the hub. No archaic time-sucking threaded indicators here!

The Micro Modular Bearing Press is designed with smaller hub and suspension bearings in mind. With drifts to service bearings with an inside diameter of 13 millimeters and smaller, this is a great choice for those smaller, more delicate bearings. The press head features a true thrust bearing; this unique feature keeps the press action super smooth and cuts down on the effort required. The thrust bearing isolates all of the torque from the compression, which allows your bearing to go in square. It works so well that you don't need even need handles. The press head has a 6mm hex in the top of the press head so you can use it as a bail out gear in case you find something that is fitting excessively tight. Drifts included to precisely fit bearing sizes: - 608 - 608_9 - 609 - 619 - 688 - 6000 - 6001 - 6701 - 6800 - 6801 - 6802 - 6900 - 6901 - 6902

We made a modular bearing press without handles and instead cut an 8mm hexagonal hole in the top. This allows you to use an allen wrench when you do run across that odd job that requires a bit of extra leverage. Instead of making a press for hubs, another for bottom brackets, and a third for head tubes, we covered all three with one modular press system. The modular system consists of a press head, press shaft, shaft extension, and our patent-pending split nut. This keeps the press manageable for hubs and bottom brackets and allows you to extend the press for tall head tubes. One of the most unique things about our press is the Split Nut. It's basically a nut that's cut in half and held close by industrial magnets. The hinged unit allows you to place it anywhere on the press shaft with no need to wind it down endlessly to press in a bearing. It also takes care of the pinch hazard that some other presses are known for. The press head features a large ball thrust bearing. This keeps the press action super smooth and cuts down on the effort required. Drifts included: PF-30, Shimano press fit, GXP press fit, 1.5" headset, 1.125" headset, centering cone. Drifts can be custom made as needed for specific applications.

Instead of making a press for hubs, another for bottom brackets, and a third for head tubes, we covered all three with one modular press system. The modular system consists of a press head, press shaft, shaft extension, and our patent-pending split nut. This keeps the press manageable for hubs and bottom brackets and allows you to extend the press for tall head tubes. One of the most unique things about our press is the Split Nut. It's basically a nut that's cut in half and held close by industrial magnets. The hinged unit allows you to place it anywhere on the press shaft with no need to wind it down endlessly to press in a bearing. It also takes care of the pinch hazard that some other presses are known for. The press head features a large ball thrust bearing. This keeps the press action super smooth and cuts down on the effort required. This handled version receives a pair of 4.5" (115mm)-long handles. Drifts included: PF-30, Shimano press fit, GXP press fit, 1.5" headset, 1.125" headset, centering cone. Drifts can be custom made as needed for specific applications.